Baterias e Acessórios ROBOTIS

Especificações

• Usa pilhas do tipo AA
• Compatível com o OLLO (CM-100, CM-100A), que usa duas caixas de pilhas

**pilhas não incluídas

SMPS2 Dynamixel

This device provides power from the SMPS to the dynamixel.

INSTRUCTIONS

• Connect the SMPS (for CM-5) to the DC terminal and connect the dynamixel using the cable.
• There are two 3P connector for AX series and two 4P connector for DX/RX series mounted on the SMPS2Dynamixel. The power and communication line are all connected making it possible to operate as the dynamixel expansion bus.
• When controlling the dynamixel with the USB2Dynamixel, power can be supplied to the dynamixel.
• Can be used by connecting to a proper DC terminal.
• Can be used according to the voltage of the dynamixel; be careful that the maximum supply voltage does not exceed 20V.
• A shrink tube is used to cover the circuit board to protect it from a short circuit which can be caused by metal in contact with the board.

PACKAGE CONTENTS

• SMPS2Dynamixel x 1pc

WARNING

** Please use the recommended voltage for every product.  Using more than the recommended voltage may damage the circuit and void the warranty.

 [e-Manual]

Especificações

• Este carregador é destinado para a bateria recarregável ROBOTIS Bateria Li-ion 3.7V 1300mAh LB-040
• Pode ser instalado em robôs com a ajuda dos ribetes OLLO
• Pode ser usado como uma moldura para fixar a bateria nos robôs.
• Carregando: LED vermelho, Carga completa: LED desligado
• Usa os cabos 2P para caixas de bateria para se conectar ao controlador (robô).

A bateria de ião lítio é uma bateria recarregável com uma carga de 1300mAh e foi desenhada especialmente para ser usada com o ROBOTIS-MINI. Nela está incorporada também um PCM para proteger a bateria de sobrecarga, descarga, e corrente excessiva.

Especificações

• Para usar com o ROBOTIS-MINI
• Modulação por Código de Pulso (PCM) integrada para proteger a bateria
• Pode ser carregada com o LBB-040
• Compatível com os controladores CM-150 e OpenCM9.04

  Essa bateria NÃO pode ser conectada diretamente ao controlador. É necessário usar o Conjunto de Carregador de Bateria Li-ion LBB-040 para tal finalidade

LIPO Battery Charger LBC-010

• This charger is intended for use with the Li-Po battery.
• The SMPS 12V 5A is required for charging through this unit.
• Support 2S and 3S Cell charge. (Exception, does not charge simultaneously)

PACKAGE CONTENTS

•  LIPO Battery Charger LBC-010 x 1 pc

* Battery and SMPS 12V 5A sold separately.

HARDWARE SPECIFICATIONS

PRECAUTIONS:

• Do not apply heat, water or any other liquid on the battery.
• Do not take the battery apart.
• Do not use damaged batteries that are inflated, deformed, damaged, etc.
• Do not charge 2S and 3S cells together at once.
• When charging, make sure the battery is connected with the correct polarities.
• Do not charge when the battery is hot. Please charge after it has cooled off.
• Do not charge the battery when it is being used by the controller.

- When the battery is not being used or is fully charged, please do not have it connected to a device to avoid complete discharge or damage

COMPATIBLE PRODUCTS

• LIPO 11.1V Battery Set LBS-010

LIPO Battery 11.1V 1000mA LB-010

• This LiPo battery is intended for the BIOLOID Premium Kit.
• Embedded PCM to protect from overcharge, discharge, and excessive currents.

PACKAGE CONTENTS

* LIPO Battery Charger LBC-10 sold separately.

HARDWARE SPECIFICATIONS

WARNINGS

• Do not drop or modify parts of the battery.
• Do not fold the end of the sutured portion.
• Do not apply heat, water or any other liquid on the battery.
• Do not place in the microwave, washing machine or dryer.
• Do not use damaged batteries that appear inflated, deformed, damaged, etc.
• Do not short circuit the battery.
• Do not disassemble the battery.
• When charging, make sure the battery is connected with the correct polarities.
• Do not charge when the battery is hot. Please charge after it has cooled off.
• Battery will not charge when connected to the robot.

When the battery is not being used or is fully charged, please remove it from the unit or charger.

STORAGE

• Detach the battery from the robot or controller before storing.
• When storing the battery for a long time, make sure the battery’s life is about 50%.

LIPO Battery 11.1V 1000mA LB-011

• This Battery is for DARwIn-OP only.
• PCM is embedded to protect from overcharging or discharge due to excess current.
• Can not be used with the BIOLOID due to the incompatible connector.
• Battery case/cover and extension cable are not included.

PACKAGE CONTENTS

• LIPO 11.1V Battery Set LBS-11 x 1pc

**Charger sold separately.

HARDWARE SPECIFICATIONS

WARNINGS

• Do not drop or modify any part of the battery or cables.
• Do not fold the end of the sutured portion.
• Do not apply heat, water, or any other liquid on the battery.
• Do not place it in the microwave, washing machine, or dryer.
• Do not use damaged batteries that appear inflated, deformed, damaged, etc.
• Do not short circuit the battery.
• Do not disassemble the battery apart.
• When charging, make sure the battery is connected with the correct polarities.
• Do not charge when the battery is hot. Please charge after it has cooled off.
• Battery will not charge when connected to the robot.
• * When the battery is not being used or is fully charged, please do not have it connected to a device. 

STORAGE

• Detach the battery from the robot or controller when storing away.
• When storing the battery for a long time, make sure the battery life is about 50%.
• Do not store in wet or hot places.

** The warranty for the LIPO Battery 11.1V 1000mA LB-011 is 6 months.

COMPATIBLE PRODUCTS

• Robot : DARwIn-OP
• Charger : LIPO Battery Charger LBC-010

** NOT compatible with CM-series controllers.

NIMH 9.6V Battery Pack NBP-10

• Battery for BIOLOID Beginner and Comprehensive Kits only.

PACKAGE CONTENTS

• NIMH 9.6V Battery Pack NBP-10 x 1pc.

HARDWARE SPECIFICATIONS

• 9.6V, Ni-MH
• 1.2V, AA type x 8pc / Package
• Weight : 242g
• Battery supply for CM-5

SMPS 12V 5A PS-10

• For the BIOLOID's - Power Supply and Charging
• Supplies power to the LIPO Battery Charger LBC-10

PACKAGE CONTENTS

• SMPS 12V 5A PS-10 x 1 pc
• AC Cord x 1 pc

SPECIFICATIONS

• 12V 5A SMPS
• 50~60Hz
• Input : 100~260V AC (Free Volt)

COMPATIBLE PRODUCTS

• CM-5, CM-510, CM-530, CM-2+, CM-700,

DARwIn-OP, SMPS2Dynamixel, LIPO Battery Charger LBC-10

This product is a rapid battery charger containing an LCD display with a high performance microprocessor and specialized operating software. The B6AC features an AUTO function that sets the feeding current during the process of charging and discharging. For Lithium batteries, it can prevent overcharging which can lead to an explosion due to the user. It will disconnect the circuit automatically and sound an alarm upon detecting any malfunction. All of the programs of this product are controlled by a two way communication to achieve maximum safety and minimize user interaction. All of the settings can be configured by the user!

Product Highlights:

• Internal independent lithium battery balancer
• Balancing individual cells battery discharging
• Adaptable to various types of lithium battery
• Fast and storage mode of lithium battery
• Automatic charging current limit
• Input power monitoring
• Cyclic charging/discharging

■ Package Contents

■Hardware Specification

■ Compatible Products (for charging)

• LIPO Battery 11.1V 1000mA LB-010
• LIPO Battery 11.1V 1000mA LB-011
• LIPO Battery 11.1V 1800mA LB-012

Please refer to the official site for more information.

http://www.skyrc.com/index.php?route=product/product&path=20_68&product_id=10

LIPO Battery 11.1V 1800mAh LB-012

• Lithium Polymer rechargeable battery (for DARwIn only).
• PCM is incorporated to protect the battery from overcharge or discharge due to excessive current.
• Cannot be used for Bioloids because the connector size is different.
• Battery cover and extension cables are not included.
• Can be charged with the LBC-10 Battery Charger.

PACKAGE CONTENTS

•  LIPO Battery 11.1V 1800mAh LB-012 x 1pc

* Battery Charger (LBC-10) sold separately

HARDWARE SPECIFICATIONS

WARNINGS

• ** Cannot be charged via DARwIn and needs to be charged using the LBC-10 charger.
• Do not drop or modify parts of the battery.
• Do not fold the end of the sutured portion of the battery.
• Do not apply heat, water or any other liquid on the battery.
• Do not place in the microwave, washing machine or dryer.
• Do not use damaged batteries that appear inflated, deformed, damaged, etc.
• Do not short circuit the battery.
• Do not disassemble the battery.
• When charging, make sure the battery is connected with the correct polarities.
• Do not charge when the battery is hot. Please charge after it has cooled off.
• The battery will not charge when connected to the robot.

STORAGE

• Detach the battery from the robot or controller when storing away.
• When storing away the battery for a long time, make sure the battery life is around 50%.
• Do not store in wet or hot places.

** LIPO Battery 11.1V 1800mAh LB-012 has a warranty period of 6 months.

COMPATIBLE PRODUCTS

-  Robot: DARwIn-OP

-  Battery Charger: LIPO Battery Charger LBC-10

** NOT compatible with the CM-Series controllers.